Sprayers


	Model 4520

	Model 4520 Literature Pg 1 - PDF

	Model 4520 Literature Pg 2 - PDF

		The 4520 Cold Process Sprayer from Hennes-Johnson represents the Roofing Industry standard for the airless application of Modified Bitumen Adhesives, Elastomeric Coatings, and Waterproofing Emulsions. With a perfect balance of 4500 psi fluid pressure, 5 gpm flow, and 20 hp Honda driven hydraulic power pack, the model 4520 is ready to handle your toughest spray demands including applications using dual tip nozzles and multiple spray guns. Our innovative direct feed design makes working from 55 gallon drums a “snap” and is easily adapted to draw from transportable bulk tanks and large capacity tankers.

TECHNICAL DATA
Working Pressure	4500 psi ( 280 bar )
Max. Cycles Per Min.	60
Gallons Per Minute	5 US (18.90 liter)
Length	70 in.
Height	70 in.
Width	39 in.
Shipping Weight bare	950 lbs. ( 430 kg)

STANDARD FEATURES

20 hp Honda V-Twin gasoline engine with electric start, low oil shut-down, full pressure lubrication,
and side discharge exhaust system.
Quick displacement pump change out ability for increased versatility.
Easy to use dashboard controls with multi function pressure gauge.
12 volt DC component access port for instant power link to in-line heating unit.
“No Creep” positive lift cylinder lock.
Full 2" intake tube with large flow capacity inlet screen.
Auxiliary access port to quickly add hydraulic mixers, hydraulic powered hose reels, or hydraulic transfer pumps

LOW MAINTENANCE DISPLACEMENT PUMP
Downtime from fluid contamination entering the displacement pump costs you time and money. In the past, the pump had to be removed from the sprayer and brought to a mechanic shop where it was further disassembled, cleaned, repaired, sent back to the job site, re-installed onto the sprayer and then put back into service.
With the new XTREME DISPLACEMENT PUMP featured on the model 4520, downtime is reduced to a minimum. The innovative pump design allows the operator to disassemble, service, reassemble, and return to production without having to remove the pump from the sprayer. All this in minutes instead of hours and with only a few common hand tools.

Additional Features & Benefits:

In-tank hydraulic oil filtering system for quick and easy maintenance.
Pressure readings at a glance with dash mounted pressure gauge.
Auxiliary pressure port which allows your 4520Xtreme Machine to perform double duty in operating hydraulic reels and mixers.
Positive valve lock configuration to prevent lift cylinder from creeping up.
Heat dissipating, 20 gallon hydraulic reservoir.
18" x 8.50" flotation tires for increased maneuverability over rough terrain.
Fail-safe low engine oil shutdown.
Heavy gauge tube steel framework.
Removable 6 gallon fuel cell for safe refueling away from hot engine surfaces.
Efficient component accessibility design for easy operation and maintenance.
Extended volume hydraulic oil filtering system.
Anti-stall reciprocating motor modifications.
Four point lifting eyes.


		Quick Change Displacement Pumps Customize your next spray job with pin-point accuracy by selecting one of our Quick change Lowers. From high volume/low pressure to high pressure/low volume and everything in between, the right pump will maximize your production and increase your profit potential.


	Model 4520A (with Built-in Heater)


	Model 4520A (with Built-in Heater) Literature PDF

Cold process materials such as modified bitumens and cut-back asphalts respond favorably to an increase in temperature. The viscosity of the fluid becomes more efficient and allows it to be delivered through longer lengths of hose and with greater effectiveness at the point of airless atomization. The Hennes-Johnson model 4520A with built in heater provides a significant 20 - 25 degree boost in fluid temperature giving you peak performance from a single pump package. The built in heater can be pre-warmed using our 120 volt, 2000 watt electric heating element so that you’ll have instant warm material from start to finish. The 4520A includes all of the features found on the Hennes-Johnson standard model 4520 including the tough tested 20hp Honda engine and Xtreme Pump System combination. Easy to use dashboard controls and gauges make operating this pump simple and efficient.

TECHNICAL DATA

Working Pressure

4000 psi ( 280 bar )

Max. Cycles Per Min.

60

Gallons Per Minute

5 US (18.90 liter)

Heating Element

single, 2000 watt

Length

70 in.

Height

70 in.

Width

39 in.

Shipping Weight ( bare )

1060 lbs. ( 461.25 kg )


		STANDARD FEATURES Dependable, V-Twin Honda 20 hp gasoline engine, featuring efficient overhead valve design and full pressure lubrication. Keyed electric starter and maintenance free electronic ignition ensures dependable, easy starts every time. Powerful, 4500 psi @ 5 gpm double ball displacement pump and Viscount II reciprocating hydraulic motor for spray application of a wide variety of cold process materials. Exclusive, Hennes-Johnson built heat transfer coil for high efficiency heating capabilities. Hydraulic lift tower allows for the displacement pump to be immersed directly into the material container providing the greatest amount of intake efficiency. Full 2" intake tube with large flow capacity inlet screen.



		HJ5320 Xtreme

		HJ5320 XTreme Literature PDF


	When specialty coating situations call for a ultra high pressure - medium volume spray system, the Hennes Johnson model 5320 is ready and able to meet the challenge. At 4900 psi with 3 gallons per minute flow, the 5320 is an ideal sprayer for elastomeric coatings where drums or collapsible transportable tote bags are specified. The very high pressure displacement pump will support three to five hundred feet of hose and still provide maximum efficiency at the point of spray delivery.

		STANDARD FEATURES: Dependable Honda, 20hp V-Twin, electric start gasoline engine featuring efficient overhead valve design and full pressure lubrication. Versatile, 4900 psi @ 3 gpm double ball displacement pump with improved intake design and Viscount II reciprocating motor for the spray application of the widest variety of cold process materials. Hydraulic Lift Tower for direct displacement pump immersion. Component ready engineering for addition of HJ1000 In-Line Heating System. Full 2" intake tube with large flow capacity inlet screen. Accessory ready for hydraulic mixers, hose reels, ect.




	HJ1000LP

	HJ1000LP Mastic Warmer Literature PDF

IN LINE HEATING SYSTEM

Today's high solid/low solvent based cut-back asphalt and SBS Modified materials are the cutting edge technology used in producing environmentally friendly yet superior quality roof systems. Along with the development of these hybrid materials comes the need to strictly maintain proper temperatures at the point of application in order to boost the pumping system's overall pressure and transfer capabilities. The HJ1000 In-Line Heating System from Hennes-Johnson excels above all others by bringing together superior design technology with rugged construction, along with our primary consideration to operator safety. Dual temperature controls monitor both the heating oil and product outlet temperatures to within plus/minus 5 degrees offering the operator complete temperature control. Each HJ1000 In-line Heater is shipped complete with heat transfer oil, nurse hose, and 12 volt electrical connection, ready to be put to use immediately upon delivery. As with all Hennes-Johnson equipment, the HJ1000 is thoroughly tested under work load conditions prior to shipment, assuring peak performance on arrival.

TECHNICAL DATA

Fuel Source

LP (from liquid withdrawal tank)

Power Source

12 volt

Ignition

Pilotless Electronic Spark

Length

63 in.

Height

42 in.

Width

36 in.

Shipping Weight

1000 lbs. ( 450 kg )


			STANDARD FEATURES 200,000 btu, high efficiency liquid withdrawal propane burner. 12 volt pilotless electronic ignition. Dual LED readout gauges for visual monitoring at a glance. 600 degree heat transfer oil. 15' x 3/4" 4000 psi working pressure nurse hose. 2" ceramic insulation throughout the heating chamber



		HJ1000E

		HJ1000E All Electric Warmer Literature PDF

( All Electric In-Line Heating System )

For the gentle warming of cold process materials without the exposure to LP flame, the HJ1000E All Electric In Line Heating System from Hennes-Johnson is hands down the industry leader. Designed to achieve a 20-40 degree rise in temperature from drum to outlet port @ 2.5 gpm, the HJ1000E will help to take the edge off of temperature sensitive materials during cool spring and fall start-ups while increasing the overall efficiency of your spray system year around. Twin 2000 watt heating elements provide safe and efficient material warming.

TECHNICAL DATA
Power Source	Two 120 volt outlets
Total Wattage	4000
Total Amperage Drawn	36
Length	24 in.
Height	30 in.
Width	24 in.

Band Heaters

Band Heaters Literature PDF

For 55-gal Drums, 5-gal Pails & Power Rollers

Pre-Warm your cold process materials with these high efficient, electric band heaters with thermostat control. Simply install the heat band onto the base of a 55-gallon barrel, 5-gal metal pail or Power Roller tank, plug it in to any 120 volt (20 amp) electrical receptacle, set the thermostat, and by morning you'll have warm material ready to be applied.

HJ410

5-gal. Pail Band Heater with Thermostat

HJ410A

55-gal Drum Band Heater with Thermostat

HJ410B

Power Roller Band Heater with Thermostat

Commercial Drum & Bulk Tank Mixers


	HJ600E, HJ600G, HJ600H, HJ610 Tank Mixers Literature PDF

Cold process material manufacturers will eagerly share with you that uniform consistency of the product itself is essential to proper application, especially with materials such as aluminum coatings and modified adhesives. Hennes-Johnson commercial grade mixers offer a practical yet economical way to bring cold process materials back into the state of suspension originally intended by the coating manufacturer.




	Please contact our Webmaster with questions or comments. © Copyright 2010 Marathon Roofing Products. All rights reserved.